Existing equipment / IQ Panel 2 Plus

Switch monitoring companies with an IQ Panel 2 Plus

Identify the panel and its radio variant, then get a written assessment of account release, programming access, service terms, and activation steps.

Alarm Cost Guide editorial • Updated November 17, 2026

Data checked November 17, 2026.

Can you change monitoring companies?

A switch may be possible if the receiving company accepts your equipment and can activate its communicator. Alarm Grid lists IQ Panel 2 and IQ Panel 2 Plus systems in its takeover guidance, with a released internal communicator and programming-code access among its requirements. That describes Alarm Grid’s published process; it does not establish another company’s acceptance or approval for your particular panel.

Sources: Alarm Grid: its takeover requirements.

If the equipment came with a house, use the existing-alarm guide to organize ownership and previous-account questions before requesting a model-specific assessment.

Identify Panel 2, Panel 2 Plus, and the radio variant

ModelDocumented sensor-radio configurationSources
IQ Panel 2319.5 MHz; do not assume PowerG is installed.Alarm.com: Qolsys panel comparison
IQ Panel 2 PlusPowerG plus one legacy frequency: 319.5 MHz, 345 MHz, or 433 MHz, depending on the installed RF daughtercard.Alarm.com: Qolsys panel comparison

The Plus designation does not mean that all three legacy frequencies are available together. Ask the provider to verify the actual installed receiver, especially if equipment has been modified. Use these Qolsys-listed U.S. Verizon and AT&T LTE part numbers to identify your panel. Confirm current availability and activation eligibility with the provider.

Sources: Alarm.com: Qolsys panel comparison Qolsys: TSB 211022, 319.5 MHz part numbers Qolsys: TSB 211203, 345 MHz part numbers Qolsys: TSB 211230, 433 MHz part numbers.

Legacy radio alongside PowerGVerizon LTE exampleAT&T LTE exampleSources
319.5 MHzQS9201-1208-840QS9202-1208-840Qolsys: TSB 211022, 319.5 MHz part numbers
345 MHzQS9201-5208-840QS9202-5208-840Qolsys: TSB 211203, 345 MHz part numbers
433 MHzQS9201-4208-840QS9202-4208-840Qolsys: TSB 211230, 433 MHz part numbers

Match the complete part number from your paperwork or equipment information. If it differs from these examples, have the provider identify it rather than guessing from a few digits. Request a model-by-model assessment of the sensors you intend to keep. The cellular-carrier column and the legacy sensor-radio column describe separate parts of the configuration.

Sources: Qolsys: TSB 211022, 319.5 MHz part numbers Qolsys: TSB 211203, 345 MHz part numbers Qolsys: TSB 211230, 433 MHz part numbers.

Resolve account release and programming access separately

Qolsys says that only the dealer controlling the panel’s Alarm.com account can terminate that account. Its support guidance also says a master reset requires a valid dealer code, with no backdoor reset. Ask the account-holding dealer to confirm release explicitly; do not treat a reset or a working user code as proof of release.

Sources: Qolsys: dealer-code and account-control guidance.

For its own takeover process, Alarm Grid requests an Installer Code or Dealer Code as well as release of the internal communicator. Ask your intended provider which access it needs and how it will preserve or document existing programming. Avoid resetting the panel before that assessment.

Sources: Alarm Grid: its takeover requirements.

Check current activation requirements and older-model notices

Have the receiving provider confirm the communicator identifier, registration status, supported software, and cellular service at the installation address. Qolsys’s connectivity guidance specifically checks correct IMEI/MEID registration and suitable LTE coverage for the installed carrier. A part-number match alone is not confirmation that activation or reliable communication has been established.

Sources: Qolsys: cellular registration and connectivity checks.

Qolsys’s March 8, 2021 firmware bulletin describes an automatic-reboot issue affecting a production batch. It identifies serial-number date codes G035–G105 and J037–J105 in digits 6–9, and says the serial number is available in the panel’s About menu. Ask the provider to check the serial number and software/build against the bulletin and confirm any required corrective update. This historical notice does not mean every IQ Panel 2 Plus is affected.

Sources: Qolsys: TSB 210308 firmware notice.

For the U.S. Verizon and AT&T models listed above, Qolsys ended sales of the 319.5 MHz pair on October 22, 2021. Sales of the 345 MHz pair (QS9201-5208-840 and QS9202-5208-840) ended on December 3, 2021. Sales of the 433 MHz pair (QS9201-4208-840 and QS9202-4208-840) ended on December 30, 2021.

Sources: Qolsys: TSB 211022, 319.5 MHz part numbers Qolsys: TSB 211203, 345 MHz part numbers Qolsys: TSB 211230, 433 MHz part numbers.

The 345 MHz and 433 MHz Telus LTE variants remained available through the December 2021 ordering changes. Qolsys discontinued both Telus variants separately on March 14, 2022. Ask your prospective provider whether it can activate your specific panel today.

Sources: Qolsys: TSB 211203, 345 MHz part numbers Qolsys: TSB 211230, 433 MHz part numbers Qolsys: TSB 220314, Telus end of sale.

Use this provider-assessment request

Please confirm whether you will accept my existing IQ Panel 2 Plus. I can provide its complete part number, installed legacy radio, sensor models, software/build, carrier, and communicator identifier privately. What account release and programming access do you need? Which devices and app features will you retain? Please itemize setup, equipment, monitoring, and required add-ons, explain the contract and cancellation terms, and describe the activation and signal-testing process.

Compare written quotes without assuming a takeover price

The FTC recommends written estimates and a contract package that sets out installation charges, monitoring fees, duration, warranty, and cancellation information. Use the following prompts to organize the assessment; this guide supplies no provider rates.

Sources: FTC: home-security shopping guidance.

Quote categoryAsk the providerSources
Setup and activationWhich assessment, programming, installation, and testing work is included? What is charged once?FTC: home-security shopping guidance
Equipment and warrantyWhich devices will be reused or replaced, why, and who handles repairs?FTC: home-security shopping guidance
Ongoing serviceWhat monitoring, cellular, app, or video services are included, and how often are they billed?FTC: home-security shopping guidance
Contract and cancellationWhat term, cancellation conditions, and remaining obligations apply to each agreement?FTC: home-security shopping guidance

Enter your quoted setup, equipment, and recurring charges in the home-security total-cost calculator, using the same comparison period for each offer. Keep old-contract cancellation charges separately identified; the calculator excludes cancellation charges. Bring the quote checklist and review monitoring arrangements when asking who receives each alert and what happens next.

Confirm the handover before calling it complete

  • Agree when the existing service ends and the new service begins.
  • Arrange provider-directed communication and sensor tests, and obtain confirmation that the intended monitoring service received the test signals.
  • Review authorized users, contact lists, and app access with the provider.
  • Keep the written equipment assessment, activation confirmation, quote, and agreement together.

Sources and document dates

Product documents describe named equipment. Provider pages describe that provider’s own offering. Undated means no publication or revision date was exposed by the opened source.